
CONCRETE HARDENER
Concrete Hardener Water-Based Treatment
Sold online on zyax.in by Zyax Chem Pvt Ltd, the company behind Flagstone Fix.
Description
Faber CONCRETE HARDENER is a water-based concrete hardener for grinding and polishing that improves the process on concrete surfaces. It also acts as a water-resistant, consolidating primer before a stain-resistant treatment, strengthening the surface and improving the durability of the subsequent protection.
CONCRETE HARDENER is a water-based consolidating treatment designed to improve the grinding and polishing process of concrete surfaces. It can also be used as a water-resistant and consolidating primer before applying a stain-resistant treatment to enhance protection. The product strengthens the surface and improves the performance and durability of the subsequent stain-resistant treatment.
Where to use CONCRETE HARDENER
Concrete floors, before grinding and polishing, and as a primer before a stain-resistant treatment.
Key benefits of CONCRETE HARDENER
- Strengthens and consolidates the concrete surface
- Improves the grinding and polishing process
- Water-repellent primer before stain-resistant treatments
- Improves the durability of the protection applied over it
CONCRETE HARDENER compared with other Faber water-repellent treatments
| Product | Best for |
|---|---|
| HIDRO PROTECTOR MM | Very high performance, water-based; also stain-resistant on polished and compact surfaces |
| PROTEX WB | High performance, water-based; stain-resistant on polished and compact surfaces, including dark honed finishes |
| HIDRO SST | Water-based; ideal for treating all 6 sides of stone tiles (install with high-quality adhesive or mechanical fixing) |
| TX 8 | Concentrated, water-based and VOC-free; diluted on site, 5 L treats over 300 m² |
| DPS | Solvent-based; also protects stone already damaged by humidity and salt efflorescence |
| SOL 170 | Solvent-based; pre-grout treatment, or deep protection against rising damp |
| DREP | Solvent-based and low-odour; for natural stone and absorbent materials |
| LIMESTONE DENSIFIER | Consolidator and honing primer for soft, very porous stones such as limestone |
| CONCRETE HARDENER | Consolidator and honing primer for concrete surfaces |
Not sure which product you need?
Every surface and finish behaves differently. Send us a photo of the surface and the approximate area on WhatsApp at +91 87792 40420 or email info@zyax.in, and our team will recommend the right product and quantity.
Product information based on Faber Italy technical documentation.
Coverage: about 10–15 m² (108–161 sq ft) per litre per coat, according to Faber’s technical data sheet. Actual coverage depends on how absorbent the surface is. Work out how much you need with our coverage calculator.
Guide: for how and when to use it, read how to stop concrete floor dusting.
How to use
- Clean surface of dust and dirt; protect adjacent surfaces
- Use during mechanical polishing on surfaces sanded with 200/400 grit (preferably dry; if wet-sanded wait 24-48 hours)
- Apply an abundant, even layer on dried, cleaned, sanded material
- On very absorbent surfaces apply a second coat 1-2 hours after the first
- Proceed to next polishing grit no less than 4 hours later (ideally next day), polishing with water
| Dilution | Ready to use, no dilution |
|---|---|
| Coats | One; second coat after 1-2 hours on very absorbent surfaces |
| Drying and curing | Wait at least 4 hours before next polishing grit; ideally next day for full cure |
| Application temperature | +5 to +40°C |
| Tools | Brush, lambswool applicator, roller, airless |
Before you start:
- Never apply to wet surfaces (slightly damp acceptable)
- Wait for concrete to dry and cure completely before applying
Directions summarised from the Faber technical data sheet. Read the full data sheet (PDF).
