Water-Based Sealer for Polished Marble and Granite: Site Guide

A practical site guide to diluting and applying a water-based stain-proof sealer on polished marble and granite, before or after laying.

The best time to apply a water-based sealer for polished marble and granite is early in a project, when the stone looks its best. The trouble starts soon after. Moisture and dirt can be absorbed during installation and leave stains that are hard to remove. Once the space is in use, tea, coffee, oil and water marks follow. On a large villa, hotel lobby or office floor, sealing hundreds of square metres with ready-to-use sealer also means a lot of cans to buy, carry and dispose of.

This guide is for contractors, site engineers and homeowners managing a stone installation. It explains how to use Faber TX 8, a concentrated water-based stain-proof and water-repellent treatment that you dilute with water on site, to protect polished and finely honed natural stone without changing its colour.

Water-based sealer for polished marble: Faber TX 8

What Faber TX 8 is (and when to use it)

Faber TX 8 is a water-based impregnator for natural stone that is sold as a concentrate. It is developed to give strong stain resistance to polished and finely honed materials. According to its technical data sheet, it:

  • gives water and oil repellency to polished and finely honed surfaces;
  • does not change the colour of the stone;
  • does not create a film or patina;
  • is long-lasting and suitable for interiors and exteriors.

It is used on marbles, granites and other natural stones, including travertine, limestone, quartzite and sandstone. It is sold in 5 litre containers, and one litre of pure product covers about 130 m2 once diluted.

Timing is flexible. Faber TX 8 is often recommended before setting, to avoid absorption stains on the stone, but it can also be applied after setting and before grouting. The data sheet adds that it does not noticeably affect how well tile adhesive bonds to the back of the treated stone.

When to be careful: the data sheet says not to apply it to dark materials, or to test first to find the right method and avoid whitish residues. That matters for black granite and dark marbles.

What you need

  • Faber TX 8 (5 litre containers)
  • Clean tap water and a marked bucket for measuring the dilution
  • Applicator: brush, lambswool applicator, roller, cloth or sprayer. Loose slabs or tiles can also be treated by immersion.
  • Lambswool pad, brush or roller to even out the residue
  • Protective gloves and eye protection

Step-by-step: applying a water-based sealer for polished marble

  1. Test first. Treat a small area or a spare piece and check the final look, especially on dark stone.
  2. Prepare the stone. The surface must be free of dust and either dry or slightly damp.
  3. Dilute. Mix 1 part Faber TX 8 with 4 parts tap water (1:4, five parts in total) or 1 part with 5 parts water (1:5, six parts in total).
  4. Apply evenly and generously by brush, lambswool, roller, sprayer or immersion. Use the coverage figures as your guide: 21 to 24 m2 per litre of solution at 1:4, or 23 to 26 m2 per litre at 1:5. One litre of pure product makes enough solution for about 130 m2.
  5. Even out the residue. After 5 to 10 minutes, go over the surface with a lambswool pad, brush or roller, spreading the remaining product until all residues are removed. (In a factory, this is done after just a few seconds.)
  6. Wait before the next trade. Leave at least 24 hours after treatment before setting or grouting.
  7. Clean up. Wash tools and buckets with water when you finish.

Tips and common mistakes

  • Do not skip the residue step. The data sheet calls for spreading the leftover product until all residues are removed, and warns of whitish surface residues on dark materials.
  • Measure the dilution properly. Guessing leads to uneven protection across a large floor.
  • Treat stone before it reaches dusty areas of the site, or clean it thoroughly first. Dust trapped under the treatment spoils the finish.
  • Plan the 24-hour wait into the programme so grouting teams are not held up.
  • Keep a spare treated tile for future colour and stain comparisons.

Safety and storage

The concentrate is alkaline (pH about 11). The data sheet lists it as causing skin irritation and serious eye irritation.

  • Wear protective gloves, clothing and eye protection. Wash hands thoroughly after handling.
  • If on skin, wash with plenty of soap and water. If in eyes, rinse cautiously with water for several minutes, removing contact lenses if easy to do, and keep rinsing. If skin irritation occurs, see a doctor.
  • Take off contaminated clothing and wash it before reuse.
  • Keep the container tightly closed in a cool, dry place, out of reach of children. Shelf life is 36 months in the original sealed pack.

Frequently asked questions

Can I use Faber TX 8 on black or dark granite?

The data sheet says not to apply Faber TX 8 to dark materials, or to run a test first to check the right application method and avoid whitish residues on the surface. On dark stone, always test before committing.

How much area does one litre of Faber TX 8 cover?

One litre of pure product, once diluted, covers about 130 m2. The diluted solution covers 21 to 24 m2 per litre at 1:4, or 23 to 26 m2 per litre at 1:5.

Can Faber TX 8 be applied after the stone is laid?

Yes. It is often recommended before setting to avoid absorption stains, but it can also be applied after setting and before grouting. Wait at least 24 hours after treatment before grouting.

Need help?

Order Faber TX 8 from Flagstone Fix as your water-based sealer for polished marble and granite on your next installation, and ask us if you are unsure which dilution suits your stone. If you would rather hand the job over, our team offers Marble Cleaning + Sealing for new and existing floors. WhatsApp us on +91 87792 40420.

Products mentioned in this guide

Share your love
Chat with us