Strippable Coating for Glass and Metal on Construction Sites

Long builds need tougher protection. A solvent-based strippable coating shields glass and metal from weld slag, grease and chemicals for months.

A strippable coating for glass and metal solves a common site problem: on a building site, finished glass and metal are exposed for months. Window glazing, aluminium and steel frames, lift doors and railings are installed long before the last trades leave. Welding throws slag, masons splash mortar, and facade cleaning uses acid or alkaline chemicals. Light-duty films do not survive that long or that much abuse.

This guide is for site engineers, facade and glazing contractors, and project managers who need tough, long-term temporary protection. It explains how to use Flagstone Fix Peelable Coating: Solvent-Based, a strippable film that is acid and alkali-proof and peels off by hand when the work is done.

Strippable coating for glass and metal: Flagstone Fix Peelable Coating: Solvent-Based

What Flagstone Fix Peelable Coating: Solvent-Based is (and when to use it)

It is a solvent-based polymer coating for temporary protection on many substrates, including glass, metal and plastics. It protects against dust, stains, grease and even weld slag, and peels off when protection is no longer needed, with no damage to the surface and no residue left behind. The data sheet lists it as acid and alkali-proof, fully hand-peelable, high in film strength and drying at room temperature. It is intended to protect surfaces during manufacturing, storage, transportation or painting.

It comes in green, orange and blue, which makes coated areas easy to spot on site. The data sheet gives an applied life of about 8 to 9 months outdoors and 15 months indoors.

How it differs from the water-based version: choose this one for longer, harsher exposure such as welding, chemicals and months of weather. For short indoor jobs in occupied homes, the non-flammable water-based coating is easier to live with.

What you need

  • Flagstone Fix Peelable Coating: Solvent-Based (do not thin)
  • Spray equipment, a dip tank or a brush
  • Masking tape for a pull-tab edge
  • Thinner for cleaning equipment
  • Solvent-resistant gloves, eye protection and a suitable respirator in enclosed spaces
  • Non-sparking tools for cleaning up spills

Step-by-step: applying a strippable coating for glass and metal

  1. Clean thoroughly. Remove dust, grease and contaminants. The film peels best from a perfectly clean surface.
  2. Tape one edge to give yourself a starting tab for peeling later.
  3. Do not thin. The product is supplied ready to spray. It is also suitable for dip or brush application.
  4. Apply the first coat evenly over the whole surface. On perfectly cleaned glass the data sheet gives about 120 sq ft per litre for the first coat.
  5. Let it dry. It is touch-dry in about 15 minutes and completely dry in about 35 minutes at room temperature. Humidity and temperature affect this.
  6. Apply the second coat. Two coats are mandatory for good peelability; the second covers about 160 sq ft per litre. Apply more coats if needed for adequate coverage. These figures are for perfectly cleaned glass, so expect lower coverage on textured surfaces.
  7. Leave it on for the job. Plan removal within about 8 to 9 months outdoors or 15 months indoors.
  8. Peel off by hand from the taped edge once the work is complete.
  9. Clean equipment with thinner, not water.

Tips and common mistakes

  • Never rely on a single coat. It may not peel cleanly, and the manufacturer gives no warranty for it.
  • Use the colours. Bright green, orange or blue film shows instantly which panes or frames are protected and which have been missed.
  • Do not leave it beyond its applied life. Remove it within the time given, especially on sun-exposed facades.
  • Test on stone and painted finishes. The data sheet names glass, metal and plastics, so check a small area first on any other surface.

Safety and storage

This is a flammable, solvent-based product with a flash point of 30°C and a VOC content of 60 to 70%. Keep it away from heat, sparks and naked flames, including welding in progress. Ventilate well, wear solvent-resistant gloves and eye protection, and use a suitable respirator in enclosed areas. Clean spills with non-sparking tools. Dispose of dirty solvent and cleaning rags safely and in line with local rules. Store in a cool, dry place with containers closed. Shelf life is 9 months from manufacture. Keep away from children.

Frequently asked questions

How long can the coating stay on?

The data sheet gives an applied life of about 8 to 9 months for external or outdoor applications and about 15 months for internal or indoor applications.

Do I really need two coats?

Yes. The data sheet says two coats are mandatory for proper peelability, and the manufacturer gives no warranty if only a single coat is applied.

Can I thin it for spraying?

No. The data sheet says not to thin or reduce it; it is supplied ready to spray. It can also be applied by dip or brush.

Need help?

Buy Flagstone Fix Peelable Coating: Solvent-Based from Flagstone Fix when your site needs a strippable coating for glass and metal. When the build is done, our Facade Cleaning & Sealing team can clean and protect the stone elevation. WhatsApp us on +91 87792 40420.

Products mentioned in this guide

Share your love
Chat with us