Clear Polyester Resin for Stone Slabs: A Fabricator’s Guide
Fabricators and stone yards use clear polyester resin to fill natural cracks and bond slabs. Ratios, working times and finishing tips.

Fabricators reach for clear polyester resin for stone because natural stone comes out of the quarry with fissures, open veins and small voids. Marble, onyx-veined slabs, granite and travertine often need filling before they can be polished and sold. Fabricators also need to bond pieces for edge build-ups, mitred joints and inlay work. The filler has to be clear enough to let the stone’s own colour show and strong enough to be ground and polished with the slab.
This guide is for stone processing units, fabrication workshops and restoration contractors. It explains how to use Flagstone Fix Waterclear Gel Special, a clear polyester resin for filling cracks and bonding stone.

What Flagstone Fix Waterclear Gel Special is (and when to use it)
Flagstone Fix Waterclear Gel Special is a two-component product based on unsaturated polyester resin dissolved in styrene, with mineral fillers. The data sheet says it is mainly used in the stone processing industry for bonding natural and artificial stones, and that its liquid-like consistency suits filling large areas. It also has a creamy-soft consistency that works well on vertical surfaces.
Listed qualities include good working properties (grinding, milling, drilling), good polishing properties, fast hardening and UV stabilisation. The data sheet gives a tensile strength of 55 to 65 N/mm² and a bending strength of 75 to 85 N/mm². It suits granite, marble and other natural stone, as well as artificial stone.
Limits: it has a slight tendency to yellow in outdoor applications, adhesion is only moderate on fresh alkaline building materials such as concrete, and bonds frequently exposed to humidity and frost have limited durability.
What you need
- Flagstone Fix Waterclear Gel Special and liquid hardener
- A scale accurate to the gram
- Mixing cups, spatulas and a squeegee or flat blade for spreading over slabs
- Fine abrasive paper and an air blower or brush
- Polyester colour paste if tinting (up to 5%)
- Hand gloves and eye protection
- A suitable cleaner for tools
- Grinding and polishing line or hand tools for finishing
Step-by-step: using clear polyester resin for stone
- Prepare the slab. The surface must be clean, dry and lightly abraded. Blow or brush dust out of the cracks.
- Keep conditions warm and dry. Hardening is accelerated by heat and delayed by cold. Avoid damp slabs, which are common in yards during the monsoon.
- Tint if needed. Add polyester colour paste up to a maximum of 5%. Keep it clear for veined or translucent stone.
- Weigh the hardener. Add 1 to 4 grams of liquid hardener to 100 grams of mastic and mix both components properly.
- Use it promptly. At 20°C working time is about 12 to 14 minutes with 1% hardener, 8 to 10 minutes with 2%, 7 to 9 minutes with 3% and 6 to 8 minutes with 4%. Mix small batches.
- Fill or bond. Spread the resin into cracks and voids, pressing it in so it penetrates. For bonding, keep layers as thin as possible, under 2 mm, because the resin shrinks about 2 to 8% and gives off heat while hardening.
- Use less hardener for big fills. When filling bigger holes or modelling corners and edges, use as little hardener as possible.
- Clean tools with an appropriate cleaner before the resin hardens.
- Wait 24 hours. Treated parts can be further processed after 24 hours.
- Grind and polish the slab as normal so the filled areas sit flush and clear.
Tips and common mistakes
- Do not exceed 4% hardener. Higher portions reduce adhesion and spoil surface drying. Below 1%, or under 5°C, hardening is greatly delayed.
- Thin is strong. Thick bond lines shrink and heat up more, which can stress the joint.
- Plan for the cure. This clear polyester resin for stone needs 24 hours before the treated parts can be processed, so build it into your production schedule.
- Remove spills early. Once hardened, it cannot be removed by solvents, only mechanically or at temperatures above 200°C.
Safety and storage
Use hand gloves to protect skin and wear suitable eye protection. Work in a well-ventilated area because the resin contains styrene. The data sheet says that, when worked properly, the product is generally not injurious to health. Shelf life is about one year when stored in a tightly closed container and kept free from frost. Store away from heat and out of reach of children.
Frequently asked questions
How long before a filled slab can be ground and polished?
The data sheet says treated parts can be further processed after 24 hours. Heat speeds hardening and cold slows it.
How much working time do I get?
At 20°C the data sheet gives about 12 to 14 minutes with 1% hardener, 8 to 10 minutes with 2%, 7 to 9 minutes with 3% and 6 to 8 minutes with 4%. Its general instructions quote around 3 to 10 minutes, so plan for the shorter end.
Is it strong enough for bonding pieces?
The data sheet lists a tensile strength of 55 to 65 N/mm² and a bending strength of 75 to 85 N/mm², and describes it as used mainly in stone processing for bonding natural and artificial stone.
Need help?
Order Flagstone Fix Waterclear Gel Special from Flagstone Fix for your workshop, or let our team fill and finish installed stone with our Diamond Mirror Polishing with Pinhole Filling service. WhatsApp us on +91 87792 40420.

Flagstone Fix Waterclear Gel Special

