Bring Back the Colour of Faded Slate and Sandstone

Sun and rain wash the colour out of slate, sandstone and terracotta. Here is how to bring it back with a non-yellowing colour-enhancing treatment.

To restore faded slate colour, or bring back dull sandstone and terracotta, it helps to know what went wrong. Slate, sandstone and terracotta look rich when they are new or wet. After a few summers of strong sun and a couple of monsoons, they turn chalky and pale. Patios, garden paths, staircases, rough kota and Jaisalmer paving and exposed concrete tiles all lose depth this way. Washing helps for a day; the dull look returns as soon as the stone dries.

If you want that freshly wetted colour back for the long term, plus protection against water and oil stains, a colour-enhancing impregnator is the answer. This guide explains how to use Faber Boost-S on unpolished, absorbent stone inside and outside the home.

Restore faded slate colour: Faber Boost-S

What Faber Boost-S is (and when to use it)

Faber Boost-S is a solvent-based, impregnating colour-enhancing treatment. It soaks into absorbent materials and deepens their natural colour while giving water- and oil-repellent protection. The data sheet highlights good stain resistance, a strong colour-enhancing effect and the fact that it will not yellow over time, even in direct sunlight. As an impregnating treatment, it soaks into the stone rather than sitting on top.

It is suitable indoors and outdoors on slate, sandstone, terracotta, concrete and concrete tiles, granite, limestone, marble, quartzite, porphyry, travertine, tufo, basaltina (lava stone), molten basalt, reconstructed stone and marble-concrete, marble-resin or quartz-resin agglomerates.

When not to use it: the data sheet is clear that Faber Boost-S is not suitable for polished surfaces. Use it only on unpolished, absorbent surfaces. Do not apply it on wet or humid surfaces either.

What you need

  • Faber Boost-S (ready to use)
  • A brush or clean, lint-free cloth
  • A suitable cleaner to prepare the surface
  • Masking tape and sheeting to protect areas not being treated
  • Solvent-resistant gloves and good ventilation
  • White spirit for cleaning tools

Step-by-step: how to restore faded slate colour

  1. Clean thoroughly. Remove all dust, dirt and grime. Any residue left on the stone gets sealed in.
  2. Let it dry completely. The surface must not be wet or humid. After washing outdoor paving, or after rain, allow plenty of drying time.
  3. Check conditions. Surface temperature must be between +5 and +40°C. Avoid stone that is overheated by midday sun; early morning or late afternoon works better.
  4. Do a test patch. Treat an unexposed area or a spare piece and let it dry to judge the colour change.
  5. Protect surroundings. Mask walls, plants, wooden frames and anything you do not want treated.
  6. Apply a thin, even layer. Use the brush or cloth to cover the whole surface. Coverage is around 15 to 20 square metres per litre.
  7. Even out after 5 to 10 minutes. Before the product is absorbed, spread out any residue so it is evenly distributed. This avoids blotchy patches.
  8. Hands off once it starts drying. Touching the surface while it dries can cause unevenness.
  9. Second coat if needed. On highly absorbent surfaces, apply a second coat 2 to 3 hours after the first.
  10. Allow to dry. It dries in about 1 to 2 hours. Resume using the area after 4 to 6 hours.

Tips and common mistakes

  • Thin coats win. Flooding the surface and leaving it does not give more colour; it gives patchy residue.
  • New paving needs patience. On recently laid or grouted areas, wait for the adhesive or grout to cure completely before treating.
  • Already sealed? If the stone has a water-repellent sealer, wait until it is completely dry before applying Faber Boost-S as a stain-resistant treatment.
  • Clean gently afterwards. For daily cleaning the data sheet recommends Faber Neugel or Faber Algafloor depending on the material; for heavy-duty cleaning, FABER 30 or Faber Deterfug.

Safety and storage

Faber Boost-S is solvent-based with a flash point below 21°C, so it is highly flammable. Keep away from flames, sparks, gas stoves and smoking. Ventilate well, wear suitable PPE and follow the safety data sheet. Clean tools with white spirit. Store tightly closed in a cool, dry place, away from children. Shelf life is 12 months in the original sealed pack. Available in 1 litre and 5 litre bottles.

Frequently asked questions

Can I use Faber Boost-S on polished marble or granite?

No. The data sheet says it is not suitable for polished surfaces. It is meant for absorbent, unpolished surfaces such as slate, sandstone, terracotta and concrete.

Will the darker colour turn yellow in the sun?

The data sheet states that Faber Boost-S does not yellow over time, even on surfaces exposed to direct sunlight, which makes it suitable for outdoor patios and steps.

How soon can I walk on the area?

It dries in about 1 to 2 hours and you can resume normal use after 4 to 6 hours from application.

Need help?

To restore faded slate colour yourself, order Faber Boost-S from Flagstone Fix, or book our Colour Enhancer Application service and we will clean, test and treat the stone for you. WhatsApp us on +91 87792 40420.

Products mentioned in this guide

Share your love
Chat with us